7.4 USING MUTE MODE
7. QUICK START > 7.4 USING MUTE MODE · PDF p. 22–23 · OS 1.10D
# 7.4 USING MUTE MODE 7. QUICK START 7. QUICK START This quick start will guide you through some of the basic operations to start using the Digitone II right away. First, connect it as described in section “3.3 SETTING UP AND STARTING THE DIGITONE II” on page 14. 7.1 SELECTING AND PLAYING THE PRESETS There are a large number of presets in the Digitone II that you can use in your music-making or as starting points for your own sound design. 1. Press [PRESET/KIT] to open the PRESET/KIT menu. 2. Select LOAD (PRESET) to open the LOAD PRESET MENU 3. Use the [UP]/[DOWN] keys or LEVEL/DATA to highlight a preset. 4. Press [KEYBOARD] and then use the [TRIG] keys to play and listen the highlighted preset. 5. Press [YES] to load the preset to the active track. 7.2 PLAYING THE FACTORY PRESET PATTERNS You can find a number of factory preset patterns in the Digitone II. Follow the instructions below to get started exploring your new instrument. 1. Press [PTN] and then use the [LEFT]/[RIGHT] keys to select bank A. Then press [TRIG 1] to select pattern A01. 2. Press [PLAY] to listen to pattern A01. 3. Press [PTN], and then press [TRIG 2] to cue pattern A02. It will start once pattern A01 has reached its end. Select pattern A03 by pressing [PTN], and then press [TRIG 3], and so on. 4. Press [STOP] to stop playback. 7.3 USING KEYBOARD MODE You can use the [TRIG] keys to play any track chromatically. 1. Select the track to play chromatically by pressing [TRK] + one of the [TRIG 1–16] keys. 2. Press [KEYBOARD] to enter KEYBOARD mode. The [TRIG] keys will light up in a pattern that resem bles an octave of a piano keyboard. Only lit keys are playable. 3. Play the [TRIG] keys. The preset will be pitched differently for each of the playable keys. Press [+]/[-] to transpose the virtual keyboard up or down one octave. For more information, please see “8.5.1 KEYBOARD MODE” on page 24. KEYBOARD mode is an effective way to add musical variety to your tracks. The timbre, tonality and impact of playing a preset chromatically depends on the character of the source preset. 7.4 USING MUTE MODE You can mute any of the sequencer tracks in this mode. Unlike the KEYBOARD mode, it makes no difference which track is active when this mode is activated. You can access all tracks simultaneously. 1. Make sure a pattern is playing. 2. Press the [FUNC] + [TRK] key to enter MUTE mode. 3. Press any of the [TRIG] keys to mute the corresponding track. Press again to unmute. The light of the [TRIG] keys indicates the mute status. Unlit keys are muted tracks. Lit keys are active tracks. For more information, please see “8.5.3 MUTE MODE” on page 27. 7. QUICK START 7.5 TEMPO AND METRONOME Press the [TEMPO] key to open the TEMPO menu. 7.5.1 TEMPO To change the BPM setting, open the TEMPO menu by pressing the [TEMPO] key. Use DATA ENTRY knob A or LEVEL/DATA to change tempo. Pressing the knob while turning it changes the tempo four BPM at a time. Use DATA ENTRY knob B or [UP] or [DOWN] to change the tempo in decimal steps. You can chose between a tempo for the whole project or use a separate tempo every pattern. Press and hold [FUNC], and then use DATA ENTRY knob E to switch between these modes. On the main interface screen, you can also press and hold the [ARROW] keys [LEFT] or [RIGHT] to nudge the tempo 10% up or down temporarily. Release the key to revert to the original tempo. To tap a tempo setting, hold [FUNC] and tap the [TEMPO] key in a steady rhythm. After four consecutive taps the average tempo of the taps will be calculated. By continuing tapping, the average tempo will keep on updating. You can also use an extrnal MIDI controller to tap the tempo by sending note C0 on the selected FX CONTROL MIDI channel. When in the TEMPO menu (and with PROJECT tempo mode selected), holding [FUNC] while turning DATA ENTRY knob A will not change the tempo to the selected value until [FUNC] is released. While doing this, “PREP.” flash in the bottom left corner of the screen. Nudging the tempo is very handy when manually syncing Digitone II to a turntable or an external sound source. Note that you do not need to be in the TEMPO menu to nudge the tempo. Use DATA ENTRY knob D to adjust the SWING setting of the pattern, to employ a propulsive, rhythmic groove. The swing ratio can be set to 51-80%. The default setting is equal spacing, 50%. 7.5.2 METRONOME The metronome settings controls the internal metronome of the Digitone II. Use the DATA ENTRY knobs to change the settings. METRO activates/deactivates the metronome. You can also press [TEMPO] + [YES] to toggle the metronome on/off. SIG. controls the note and beat measure of the metronome time signature. PREROLL controls for how many bars the metronome will sound before the sequencer starts playing. This setting is only relevant when you are in LIVE RECORDING mode. VOL controls the volume of the metronome click. 7.6 EDITING PARAMETERS Each track has six PARAMETER page groups that each contain a number of pages. Press [PARAMETER] keys TRIG, SYN, FLTR, AMP, FX, and MOD to access the different PARAMETER page groups. These param eters affect the sound and signal in various ways. 1. Make sure a pattern is playing. 2. Press [TRK] + [TRIG] keys 1–16 to select a track. 3. To change, for example, the cutoff of the filter, press the [FLTR] key to open the FILTER page. The parameter labeled FREQ changes the cutoff of the filter. Turn DATA ENTRY knob E to change the parameter value, and hear how the sound is affected. Try out the rest of the PARAMETER page parameters to explore a variety of sound shaping possibilities.
Chunks share pages with neighboring sections; text before/after the section heading belongs to the adjacent sections.