3.3 SETTING UP AND STARTING THE DIGITONE II
3. PANEL LAYOUT AND CONNECTORS > 3.3 SETTING UP AND STARTING THE DIGITONE II · PDF p. 14–15 · OS 1.10D
# 3.3 SETTING UP AND STARTING THE DIGITONE II 3. PANEL LAYOUT AND CONNECTORS 3.2 REAR CONNECTORS 1. POWER Switch for turning the unit on and off. 2. DC In Input for power supply. Use the included PSU-3c power adapter, connected to a power outlet. 3. USB For connecting the unit to a computer. For MIDI-control or Overbridge use. Use the included A to B USB 2.0 connector cable to connect to a computer host. 4. MIDI THRU/SYNC B, Forwards data from MIDI IN. Can also be configured to send DIN sync to legacy instruments. Use a standard MIDI cable to connect another MIDI device in the chain. 5. MIDI OUT/SYNC A, MIDI data output. Can also be configured to send DIN sync to legacy instruments. Use a standard MIDI cable to connect to MIDI In of an external MIDI device. 6. MIDI IN, MIDI data input. Use a standard MIDI cable to connect to MIDI Out of an external MIDI device. 7. INPUT L/R, Audio inputs used for external sources for audio processing. Use either a 1/4” (Tip/Ring/ Sleeve) phone plug (balanced connection) or a 1/4” mono phone plug (unbalanced connection). 8. OUTPUT L/R, Main audio outputs. Use either a 1/4” (Tip/Ring/Sleeve) phone plug (balanced connection) or a 1/4” mono phone plug (unbalanced connection). 9. HEADPHONES, Audio output for stereo headphones. Use 1/4” Tip/Ring/Sleeve phone plug. 3.3 SETTING UP AND STARTING THE DIGITONE II Make sure you place the Digitone II on a stable support, such as a sturdy table, with sufficient space for the cables. Make sure to switch off all devices before you connect the Digitone II to other devices. 1. Plug the supplied DC adapter into a power outlet and connect the small plug to the 12 V DC In on the Digitone II. 2. Connect OUTPUT L/R from the Digitone II to your mixer or amplifier. or use headphones plugged in to the HEADPHONES jack. 3. To control the Digitone II from a computer, connect a USB cable between the computer and the USB connector of the Digitone II. 4. If you want to use MIDI to control the Digitone II, connect the MIDI OUT port of the device you wish to send data from to the MIDI IN port of the Digitone II. The MIDI THRU port duplicates the data arriving at the MIDI IN port so that it can forward data to other MIDI units. If you want to use Digitone II to control other devices, connect the MIDI OUT port of the Digitone II to the MIDI IN port of the of the device you want to control. 5. Connect an audio source to INPUT L/R or via USB if you want to process audio from external sources. 6. Switch on all units. Press the POWER switch located at the back of the Digitone II to switch it on. 4. DIGITONE II SOUND ARCHITECTURE 4. DIGITONE II SOUND ARCHITECTURE The illustrations below show the Digitone II internal sound architecture for its 16 audio voices. 4.1 AUDIO VOICES SYN MACHINE BIT REDUCTION AMP FILTER ENVELOPE AMP ENVELOPE PAN DELAY SEND REVERB SEND TO MIXER CHORUS SEND OVERDRIVE SRR B-W FILTER OVERDRIVE SRR B-W FILTER FLTR MACHINE The overdrive, sample rate reduction, and the base-width filter can all individually be routed before or after the filter machine. 4.2 EFFECTS 4.2.1 SEND EFFECTS DELAY SEND CHORUS DELAY FROM EFFECT SENDS TO MIXER TO MIXER REVERB SEND REVERB SEND REVERB TO MIXER 4.2.2 MASTER EFFECTS MIXER DELAY RETURNS FROM AUDIO VOICES OUTPUT L/R HEADPHONES REVERB RETURNS FROM INPUT L/R MASTER OVERDRIVE CHORUS RETURNS COMPRESSOR
Chunks share pages with neighboring sections; text before/after the section heading belongs to the adjacent sections.