7.4 EDITING PARAMETERS
7. QUICK START > 7.4 EDITING PARAMETERS · PDF p. 23 · OS 1.15A
# 7.4 EDITING PARAMETERS 7. QUICK START press and hold the [ARROW] keys [LEFT] or [RIGHT] to nudge the tempo 10% up or down temporarily. Release the key to revert to the original tempo. To tap a tempo setting, hold the [FUNC] key and tap the [TEMPO] key in a steady rhythm. After four consecutive taps the average tempo of the taps will be calculated. By continuing tapping, the average tempo will keep on updating. You can also use an extrnal MIDI controller to tap the tempo by sending note C0 on the selected FX CONTROL MIDI channel. When in the TEMPO menu (and with PROJECT tempo mode selected), holding [FUNC] while turning DATA ENTRY knob A will not change the tempo to the selected value until the [FUNC] key is released. While doing this, “PREP.” flash in the bottom left corner of the screen. Nudging the tempo is very handy when manually syncing Digitakt II to a turntable or an external sound source. Note that you do not need to be in the TEMPO menu to nudge the tempo. DATA ENTRY knob D to adjust the swing setting of the pattern, to employ a propulsive, rhythmic groove. The swing ratio can be set to 51-80%. The default setting is equal spacing, 50%. 7.3.2 METRONOME The metronome settings controls the internal metronome of the Digitakt II. Use the DATA ENTRY knobs to change the settings. METRO activates/deactivates the metronome. You can also press [TEMPO] + [YES] to toggle the metronome on/off. SIG. controls the note and beat measure of the metronome time signature. PREROLL controls for how many bars the metronome will sound before the sequencer starts playing. This setting is only relevant when you are in LIVE RECORDING mode. VOL controls the volume of the click. 7.4 EDITING PARAMETERS Each track has six PARAMETER pages. Press [PARAMETER] keys TRIG, SRC, FLTR, AMP, FX, and MOD to access the different PARAMETER pages. These parameters affect the sound and signal in various ways. 1. Make sure a pattern is playing. 2. Press [TRK] + [TRIG] keys 1–16 to select a track. 3. To change, for example, the cutoff of the filter, press the [FLTR] key to open the FILTER page. The parameter labeled FREQ changes the cutoff of the filter. Turn DATA ENTRY knob E to change the parameter value, and hear how the sound is affected. Try out the rest of the PARAMETER page parameters to explore a variety of sound shaping possibilities. 7.5 SAMPLING FROM THE EXTERNAL INPUTS Digitakt II can also sample audio. It can sample audio from external sources, via the external inputs, and it can also sample audio internally from the Digitakt II itself. 1. Connect your audio source to the IN L/R inputs of the Digitakt II. 2. Press [SAMPLING] to access the SAMPLING menu and then use DATA ENTRY knob A to set SOURCE to IN L R. 3. Keep an eye on the input level meter and play the audio source and make sure that the volume of the audio source is as strong as possible, but without clipping or distorting. Set MON to POST MIX to monitor the incoming audio through the Digitakt II’s mixer and effects. 4. Again, with an eye on the input level meter, use DATA ENTRY knob D to set THRESHOLD just above the indicated background noise of the audio source (when it is not playing). 5. Use R.LEN to set the length of the sampling. 6. Switch ARM to ON to arm the sampler and then play the sound source. When the input audio exceeds the set THRESHOLD level, sampling will start. 7. Press [YES] when you want to stop sampling, or with an R.LEN setting of 1–128, the sampling stops automatically. The sampling also stops if it reaches the max sampling time (66 seconds). The Digitakt II then automatically normalizes the sample. 8. Use the DATA ENTRY knobs E and H to set the parameters TRIM START and TRIM END to trim the sample to the desired length. You can use the DATA ENTRY knob F to zoom in and out to make it easier to see where to trim the sample. Use [FUNC] + F to zoom vertically. Use knob G to position the
Chunks share pages with neighboring sections; text before/after the section heading belongs to the adjacent sections.